This great article down below relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is absolutely fascinating. Read on and make your own final thoughts.
Mounting a bathtub isn't specifically rocket science, but it does need solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old tub with a new one is likewise a reasonably hard project. If the old tub is easily obtainable, the task can move easily; if you need to open a wall surface to eliminate the old tub as well as place the brand-new bathtub, the job is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub and set in the new one. See to it you have certified yourself for the job and also are comfortable attempting it. Rather than working with a contractor to take over a halfway-completed task, it is much better to consider employing one before you begin. Opportunities are you may need a specialist plumber to make tube connections.
This post will aid you install a brand-new bath tub in your washroom if you have already purchased a new bathtub and don't need to change the setup of your previous supply of water pipelines.
Your tools and material checklist should make up the following:
Getting ready for the Installation
To start with, the sustaining frame provided with the bath must be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the tap features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to prevent pressure on the tub.
Fit the adaptable tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last setting.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you should do is separate the water supply. After doing so, activate the taps to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing taps can be quite troublesome due to the limited accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a cloth ready for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have been eliminated, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Before proceeding to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the called for position. The wood boards are handy in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The next goal is to make sure that the tub is leveled all round. This can be attained by inspecting the level and adjusting the feet on the tub up until the spirit level reviews degree.
To install faucets, fit all-time low of the outermost flexible faucet connector to the suitable supply pipe by making a compression sign up with; after that do the same for the other tap.
Activate the water supply and inspect all joints and also new pipework for leaks and also tighten them if required. Fill up the tub as well as likewise inspect the overflow outlet and the normal outlet for leakages.
Lastly, repair the bathroom paneling as described in the producer's user's manual. Tiling as well as securing around the bath tub must wait until the bathtub has actually been made use of at least once as this will settle it right into its final placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will need reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making certain that the washing machines are in place between the faucet and also the sink. Safeguard the tap in place with the supplier provided backnut. Once the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet adapters. The previous type ought to be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to split a rigid seal, triggering the water to pass through the wall in between the bathroom as well as the tiling, causing issues with dampness and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and also installations. They are offered in tubes and also cartridges, as well as can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the tub with water before sealing, to enable the motion experienced when the bathtub is in use. The sealer can fracture rather early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly offered on the market. It is advisable to fit the tiles using waterproof or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our excerpt about How to Install a Bathtub. Thanks so much for spending some time to read our content. In case you liked our post if you please do not forget to pass it around. Bless you for your time. Kindly come visit our site back soon.
Got trouble? Ring!